“Los pneumatic cylinders They are an important part of industrial automation, mainly through the movement of expansion and contraction to complete the action requirements on mechanical equipment.“
You can check the detailed installation video at:
1. Preparation

Assembly products and tools
- Polyurethane pneumatic hose
- 4V210-08 solenoid valve
- VSC speed control valve
- DNC standardized pneumatic cylinder ISO 6431
- DNC pneumatic cylinder - double acting double rod
- Phillips screwdriver
- open end wrenches
- adjustable wrench
- Thread sealants
- Thread sealing tape
- hexagon wrench
* Select one clean and smooth surface to install the pneumatic cylinder. Make sure the mounting position does not interfere with the movement of other mechanical parts.
2. Installation steps
① Speed control valve installation
The function of the speed control valve is to regulate the flow rate and therefore the speed of expansion and contraction of the piston rod, regulating the flow rate with a knob. It is locked with a locknut after adjustment.
Before installation, the speed regulating valve must be sealed with the help of thread sealants o thread sealing tape to ensure its tightness during operation. Screw the speed control valve into the inlet and outlet ports of the air cylinder with open-end wrenches.
Sealing method 1: Thread sealing tape
① Cut any thread sealing tape that may wrap around the connectors during 3 or 4 laps (the specific length can be calculated by the diameter of the connecting thread).
②The width of the threaded sealing tape should not exceed the bottom of the thread. If it is too wide, it can be folded and rolled. Wrap the thread sealing tapes around the thread counterclockwise. No burrs or filaments are formed and the surface after The winding is impeccable.


Note: If the raw tape exceeds the thread or is wound unevenly, it may cause raw tape residue to fall into the cylinder during the twisting process, causing the pneumatic air cylinder to malfunction.
Sealing Method 2: Thread Sealants


* Detailed installation tutorial reference: Installation and use of solenoid valve
② Solenoid valve installation
The function of installing pneumatic solenoid valve it is mainly change air source and make the piston rod reciprocate in the pneumatic air cylinder.
For detailed installation instructions, please refer to the previous article: Installation and use of solenoid valves
Insert the air hose into the work port A of the pneumatic valve and the other end in the import port at the bottom of the air cylinder.
Insert the pneumatic hose in it work port B of the solenoid valve and the other end into the retracted port at the top of the pneumatic cylinder.


Note: The air tube can be reconnected by pressing the spring on the connector to unlock and remove the air tube.
3. Security check
① Make sure all fasteners are securely fastened and do not loosen.
② Check that there are no air leaks at all connection points.
③ Make sure the entire system is safe during operation.
4. Working principle and testing
① Working principle
Power on and turn on the air source, air enters working port A from inlet port P, port A is vented to reach extension port of air cylinder and the cylinder piston rod begins to perform the extension action. Air enters port B from the retraction port and exits through port R2.
In the absence of power, the investment can be adjusted by the manual switch. By pressing the switch, air flows from inlet port P to working port B, which is vented to reach the retraction port, where the piston rod of the pneumatic cylinder is retracted. Air enters port A of the solenoid valve from the air inlet and escapes to port R1.


Pneumatic cushion adjustment
The air cushion fits to air cushion size required by turning the adjusting screw with a hex wrench, thereby protecting the cushion seals during pneumatic cylinder action and increasing the life of the air cylinder.
② Tests
– Turn on the air source and adjust the AR air regulator at the appropriate working pressure.
– Test operation several times to ensure that the pneumatic cylinder moves smoothly and that there are no leaks or air stagnation.
– Adjust the air cylinder speed control valve to obtain the ideal movement speed.
After completion of installation and testing, the pneumatic air cylinder is subjected to periodic maintenance and service to ensure its correct operation.
The above is the installation of pneumatic cylinders and accessories. If you have any questions about pneumatic cylinders or other pneumatic components, contact VPC. We will be happy to help you.
*Original content, if you wish to reproduce or quote please cite the source.










